How to install a wooden floor


You would be surprised how easy and simple it can be to install a wooden floor in your room , living room or dining room. Of course, to achieve optimal results you must have a lot of dedication and dedication. Are you ready for the action?

Did the weekend come and you do not know what to do? What do you think if we stay at home today to fix those entire imperfect you always wanted to correct. Let’s start with the wooden floor that over the years usually deteriorates due to factors such as humidity in certain areas or the natural wear and tear of the wood.

How to install a wooden slat floor

Wood tiles with plastic base allow an even easier installation because they do not need a structure of battens or rails. Its plastic base not only facilitates a perfect union between tiles, but also ensures the drainage of water. Therefore, they can also be installed on earth or sandy soils provided they are well leveled and compacted.

Image result for wooden floor

How to install a wooden floor

The wooden ipe decking floors in slats are installed on crossbeams or battens. They have the advantage that they fit on stainless staples or clicks and allow to achieve very uniform surfaces, without seeing unions or screw heads. They also prevent objects from being squeezed between the slats, since a good placement leaves no gaps between the pieces. They can be easily disassembled if you need to do any work under the pallet.

Previous preparation Prepare the base as indicated in the installation of wooden tiles. (Cut the crossbars of the correct measurements (remember that it is always advisable to measure twice) and place them on the surface in the same direction of the drop of water or slope. Presents the entire structure of crossbeams before screwing them to the ground to confirm if their distribution it’s correct). Remember to arrange the crosspieces perpendicular to the slats.

Step 1. Next, you must install the first blade.

  • If the platform is free, that is to say if it does not limit against a wall or edge, you must first screw a profile of the roof, to which you must attach the first slat. If, on the other hand, there is a wall or edge, you can directly install the first slab next to it.
  • From the first lama you must go installing the rest, one by one. First screw the staples or click system onto the rails to fit each plank on both sides. You can use a nylon head hammer to fit the profile to the clicks without damaging the wood.

Related image


Step 2. If the surface to cover is very long and you have to install two or more slats in each row, try that the joints do not coincide in the following rows, this way you will achieve a firmer structure.

Step 3. It is common for the last blade to fit into a hole smaller than it, or even at an angle. To cut it to size, measure with a flexometer the hole available from end to end and transfer the measurement to the blade marking the cut line. Then section it with a jigsaw for wood. To saw with more precision and safety, you can attach the blade to a work table with a sargenta. You can also help with a crowbar lever to fit that last blade if it is placed next to a wall.

Step 4. Finally, cut to size the finishing profiles to cover the edges free of the platform. Present them in their position and practice some guide holes to screw them to the crossbars of the base with the lag screws.

How to install wooden tiles with plastic base

Wood tiles with plastic base allow an even easier installation because they do not need a structure of battens or rails. Its plastic base not only facilitates a perfect union between tiles, but also ensures the drainage of water. Therefore, they can also be installed on earth or sandy soils provided they are well leveled and compacted.

  • They are placed directly on the base and fit one another through the system of built-in clicks, both on four sides and two or three if they are tiles for corners or edges. Some models incorporate finishing pieces for the edges of the platform.
  • You can easily cut the edge tiles with a jigsaw if you need to adjust them to a space less than your size next to an edge or a wall. To do so, you just have to measure the gap between the last tile and the edge or wall. Then you must move the measurement to the tile that you need to fit, marking with a ruler and a marker the line of cut between the two extreme points. With a jigsaw that incorporates a wood blade you can make a clean and precise cut.
  • Once installed, the tiles are fixed, immovable and are easy to dismantle if you want to change the model or do some type of work.

For more information about wooden ipe decking visit: https://buyipedirect.com.

Related Searched Articles


Leave a Reply

Your email address will not be published. Required fields are marked *